View HDBF07009B24_4657521.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SPEC NO :
SPECIFICATION
CUSTOMER PRODUCT MODEL NO PREPARED APPROVED CHARLES
SAW FILTER HDBF07009B24
CHECKED Houshihong D A T E 2007-01-25
CUSTOMER RECEIVED:
CHECKED
APPROVED
DATE
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 1 of 8
SAW FILTER
HDBF07009B24
History Record
Date Spec No Part No Customer No Modify Content Remark
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 2 of 8
SAW FILTER 1. SCOPE
This specification shall cover the characteristics of SAW filter with the page system.
HDBF07009B24
HDBF07009B24 used for
2. ELECTRICAL SPECIFICATION
DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -20 to +70 -40 to +85 0dBm
Electronic Characteristics Fo = 70.0 MHz Terminating source impedance: 50 ohm and matching network Terminating load impedance: 50 ohm and matching network Minimum Center Frequency Insertion Loss 1dB Bandwidth 3dB Bandwidth 40dB Bandwidth Amplitude Ripple (Fo +/- 4.375 MHz) Group Delay Variation (Fo +/- 4.375 MHz) Absolute Delay Ultimate Rejection Temperature Coefficient of Frequency MHz dB MHz MHz MHz dB nsec usec dB ppm/C 69.94 8.7 9.4 38 Typical 70.0 11.5 9.0 9.53 11.5 0.8 100 1.55 45 -94 Maximum 70.06 12.5 12.0 1.2 150 -
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 3 of 8
SAW FILTER
HDBF07009B24
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 4 of 8
SAW FILTER
HDBF07009B24
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 5 of 8
SAW FILTER
HDBF07009B24
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 6 of 8
SAW FILTER 3. TEST CIRCUIT
HDBF07009B24
4.DIMENSION
Dimension Pin Configuration 11 Input 5 Output Other Ground A B C D E H P
min 13.1 6.3 1.21
0.72
mm typ 13.3 6.5 1.36 1.5 0.8 0.76 2.54
max 13.5 6.7 1.51
0.80
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 7 of 8
SAW FILTER 5. ENVIRONMENTAL CHARACTERISTICS
HDBF07009B24
5-1 Temperature cycling Subject the device to a low temperature of -40for 30 minutes. Following by a high temperature of +25 for 5 Minutes and a higher temperature of +85 for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in table 1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260 5 for 101 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in table 1. 5-3 Solderability Submerge the device terminals into the solder bath at 245 5 for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in table 1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1.
6. REMARK
6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:info@shoulder.cn
Page 8 of 8

▲Up To Search▲

Price & Availability of HDBF07009B24

	To Download HDBF07009B24 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .